Three-Phase DC Power Supply RPL 2410WD-2440D
Single-phase DC power supplyRPL 122.5W – 2440WRegulated primary-switched single-phase switching power suppliesAvailable in 30W, 60W, 125W, 250W, 480W and 960WInput wide input voltage range 85-264V, 90-264V, 196-460V (depending on version) see data sheetOutput DC 12, 24 or 48V General:Primary-switched power supplies do not require a mains transformer, are compact and lightweight.Special features of the RPL series Universal input (AC or DC for single-phase or 3AC or DC for three-phase devices) with wide input voltage range Output voltage adjustable over a wide range via front-side potentiometer Power supplies of the RPL series can be used as chargers (type …WL) By simply repositioning the jumper on 250W alternating current, 480W alternating current and 480W three-phase current or by implementing the –T option on other chargers in conjunction with the installation of a temperature sensor (NTC resistor 10kΩ) on the battery, temperature-controlled charging of the batteries is activated. This leads to optimized charging of the batteries in the event of large fluctuations in ambient temperature and increases, among other things, the life expectancy of the battery Can be connected in series and parallel 25% power boost for 4s in the event of occurring peak loads Protection against overload, short circuit, overvoltage and overtemperature Three-color status LED, on devices from 125W: green – voltage stabilization, red - current limiting, yellow – device on mains, output voltage switched off Potential-free fault signaling contact (changeover contact)Options: -S: Decoupling diode (series diode) at the output for easy setup of redundancy and UPS systems; -U: Analog input DC 0-10V for adjusting the output voltage from 0 to Uout max; -D: Overload Shut Down, latching shutdown in case of overload; -P: symmetrical power distribution in parallel operation; -T: Temperature-controlled charging; -F: Remote off/on switching; -A: Fault signaling contact (alarm); -M: Minus temperature range. Is only relevant for RPL 2440D, since other devices are designed as standard for minus temperature range; -C: Mains harmonic limitation according to EN 61000-3-2 Class C (lighting systems).
Available immediately
Single-phase DC power supply RPL 122.5W – 2440W
Single-phase DC power supplyRPL 122.5W – 2440WRegulated primary-switched single-phase switching power suppliesAvailable in 30W, 60W, 125W, 250W, 480W, and 960WInput: Wide input voltage range 85–264 V, 90–264 V, 196–460 V (depending on model); see data sheetDC 12, 24, or 48V output General:Primary-switched power supplies do not require a line transformer; they are compact and lightweight.Special Features of the RPL Series Universal input (AC or DC for single-phase devices; 3AC or DC for three-phase devices) with a wide input voltage range Output voltage adjustable over a wide range via a front-panel potentiometer Power supplies from the RPL series can be used as chargers (Type …WL) By simply repositioning the jumper for 250W AC, 480W AC, and 480W three-phase AC—or by enabling the –T option on other chargers in conjunction with installing a temperature sensor (10kΩ NTC resistor) on the battery—temperature-controlled charging of the batteries is activated. This results in optimized battery charging even with large fluctuations in ambient temperature and, among other benefits, increases the battery’s service life. Can be connected in series or in parallel 25% power boost for 4 seconds during peak loads Protection against overload, short circuit, overvoltage, and overtemperature Three-color status LED, for devices 125W and above: green – Voltage stabilization, red - Current limiting, Yellow – Device connected to the mains, output voltage disabled Dry contact fault signal (changeover contact)Options: -S: Decoupling diode (series diode) at the output for easy configuration of redundancy and UPS systems; -U: Analog input DC 0–10 V for adjusting the output voltage from 0 to Uout max; -D: Overload Shut Down, memory-based shutdown in case of overload; -P: Symmetrical power distribution in parallel operation; -T: Temperature-controlled charging; -F: Remote on/off switching; -A: Fault signal contact (alarm); -M: Sub-zero temperature range. This applies only to the RPL 2440D, as other devices are designed for sub-zero temperatures as standard; -C: Mains harmonic suppression in accordance with EN 61000-3-2 Class C (lighting systems).
Delivery time on requestk
Do you have specific requirements?
We’ll provide you with personalized advice and work with you to find the right solution for your application.